60" Lightweight Foam Trailer Ramp Kit

Built For Cars That Live On The Edge Of Ground Clearance

If your car barely clears speed bumps and normal trailer doors might as well be concrete walls, the 60" Lightweight Foam Trailer Ramp Kit from APEX is the solution that finally matches how low you run. Instead of stacking wood, fiddling with makeshift blocks, and creeping forward while everyone holds their breath, these trailer ramps extend your trailer and drop the approach angle to 6.6 degrees. That is the kind of geometry low splitters and deep front lips can actually live with.

Roll up onto the ramps and the front end climbs gradually, not all at once. The nose stays off the trailer edge, the exhaust clears, and you are not listening for that sickening contact that ruins a good weekend before it starts. With this APEX kit in the trailer, loading stops feeling like a gamble and starts feeling like part of the plan.

60 Inches Of Controlled Transition

The 60 inch length and 7 inch rise are tuned for cars that need more than a token angle change. Longer wheelbases, extended aero, and heavily lowered setups all benefit from extra ramp length. That additional real estate spreads the transition out, which is exactly what you want when your front bumper is only a few inches off the ground.

At 6.6 degrees, the approach angle is shallow enough for serious street builds and many track cars that struggle with typical trailer doors. It softens the step where the trailer ramp or door begins, so you get a smooth arc instead of a sharp hinge in the path of travel. The result is a controlled, confident drive on instead of inch by inch guesswork.

APEX Ramps Structural Foam Core That Feels Solid

Inside each APEX trailer ramp is a high density structural foam core that behaves like a solid ramp under load while staying easy to handle. This is not hollow plastic or a thin shell wrapped around air. The foam core is engineered to carry thousands of pounds, distributing the load through the body of the ramp so it resists permanent compression and collapse.

Under the tire, it feels planted, not squishy. There are no hollow clunks, no metal flex, and nothing that rings or resonates. You simply roll onto a solid, stable surface that does its job without calling attention to itself.

Durable Polyurea Coating With Real Traction

The core is fully encapsulated in a rugged polyurea coating that gives APEX ramps their durability and grip. Polyurea is highly resistant to abrasion, impact, chemicals, and UV exposure, which means the coating stands up to real shop conditions, road grime, and constant loading cycles.

The surface is micro textured to grip both trailer decks and tires. On concrete, asphalt, epoxy floors, and typical trailer surfaces, the ramps are designed to stay put as the car climbs. You are not chasing ramps that want to slide away or adding rubber mats underneath just to keep things in place.

Reinforced Trailer Shelf That Stays Square

Where most foam trailer ramps eventually fail is the interface where the trailer door or ramp sits. That is the point that takes the most punishment, and over time it can compress, deform, and round off. APEX ramps solves this with a reinforced UHMW insert embedded into the shelf at the trailer contact zone.

The UHMW reinforcement carries the load at the edge of the trailer door so the shelf face stays clean and square season after season. It prevents compression and shelf deformation where the ramp rests on the door, which means the approach angle you buy is the angle you keep and loading stays predictable for every car that follows.

Light Enough For One Person, Serious Enough For Real Work

Despite the size and 7 inch height, each ramp in the 60" Lightweight Foam Trailer Ramp Kit is light enough to move and position by yourself. Integrated carry areas are molded into the ramp body, so there are no straps to rot, no bolted handles to loosen, and nothing to rattle when the trailer is on the road.

Because the ramps are solid foam with a non marring skin, you can lean them against trailer walls, set them on coated shop floors, or store them in tight spaces without worrying about rust, scratches, or sharp edges. They are quiet to use, quick to deploy, and built to live in a working trailer, not just look good in photos.

Why Choose APEX Ramps Over Generic Foam Ramps

There are plenty of generic foam ramps out there. What APEX brings to the table is a combination of tuned geometry, structural core density, reinforced trailer interface, and coating quality that is designed specifically around low car trailer loading. These are not repurposed display blocks or storage cribs. They are engineered tools for one job - getting your low car onto a trailer without contact.

If you are hauling track cars, serious street builds, or customer vehicles that cannot afford damage, this kit is the kind of quiet upgrade that pays for itself every time a front splitter clears without drama.

Who Is This Product Best For?

• Drivers of very low track cars and serious street builds that constantly fight trailer angles
• Motorsport teams and transporters hauling cars with aggressive aero packages or long overhangs
• Performance and tuning shops that regularly move customer vehicles with minimal ground clearance
• Dealers and specialty resellers transporting high value vehicles that cannot afford front bumper or splitter damage
• Enthusiasts who want an APEX level trailer solution instead of juggling lumber and guesswork